Cherry Mobile Flare J1 V2.0 Firmware / Stock Rom

Cherry Mobile Flare J1

Here is the firmware for Cherry mobile flare J1 V2.0, this has two version of build number, V02 and V04, select the right firmware below. we also add solution for touch screen, after flash touch screen not working solved.
Important Reminder:
Select the two firmware download link below and make sure you know your Build Number Version.
How to know your build number?
Go to Settings>About Scroll down to Build Number

Download Firmware
(Build Number: Cherry_Flare_J1_H130_V02_20160127)

Download Firmware
(Build Number: Cherry_Flare_J1_H130_V04_20150928)

Check Out the Troubleshooting below for the instruction for Touch Screen fix or No Signal after Flashing.

---

Flashing Stock Rom To Android Smartphone

Install Spreadtrum Driver

1. First download SPD SCI Android USB Driver V4 by jungo the complete driver for Spreadtrum.
2. After download, extract anywhere  in your computer, then select system type if 32-bit or 64-bit.
   - To know your system type, go to control panel click on System and Security then click System. or simply right click on Computer and click Properties. you will see like this. mine is 32 bit (also known as x86-bit).
   
   
3. After you knew your system type, open your extracted SCI-android-usb-driver-jungo-v4 folder, then choose a folder weather it is x86(32) or x64, then run DPInst.exe. Just click next until it finish installing.
   

NOTE: Before proceeding, make sure that your android smartphone should have atleast 30 to 50 percent of battery to perform flashing.

Flash Pac file Stock Rom

1.  Download the SPD_Upgrade_Tool_R4.0.0001 latest version, or SPD_Upgrade_Tool_R299015 lower version. Then extract to your desired location.
2. Open your extracted files and run ResearchDownload.exe, For lower version open Bin folder and run UpgradeDownload.exe.
   NOTE: UpgradeDownload and ResearchDownload is the same, UpgradeDownload is just the name of the lower version but they are both SPD Upgrade tool.
   
3. In this instruction I will use UpgradeDownload and a Use Cherry Mobile Pac file as a sample. In UpgradeDownload window, click on single gear icon to Load Packet and browse for pac file(firmware/stock rom) you downloaded then click open. follow this screenshot.
   
4. Loading a pac file may took long depend on file size. After loading a pac file, now ready to start flashing, You can also click on Settings on two gear icon if you want to unchecked some part of firmware like EraseRuntimeNV, This will not work on lower version. I recommend that leave it unchanged if you don't have any idea.
   
5.  Turn off first your phone, remove battery (if removable) then bring it back. In ResearchDownload/UpgradeDownload Click on Start Downloading, then in your phone press Volume up and Volume down then connect USB cable. If you see a a progress bar, then it means that it is successfully connected. if not, then try step 5 again.
   
6. Wait until you see a Passed in progress, that means, you installed a new stock rom successfully.
   

After you flash the firmware, you can now turn on your phone, take note that first time start up may took long. but if it tooks more than 15 minutes then I suggest to perform a hard reset. you can search a procedure in google.

---

Troubleshooting

For Touch screen not working after flash

Just download the all parts and flash it
CM Flare J2 V2 Touch Fix <== This will work also to V3,0 Build Number V06

For No Signal after flash

1. Download wfixnv1 and TerminalEmulator.
2. Copy it to SD Card directory, then install TerminalEmulator.
3. On TerminalEmulator Type su (enter)
4. Type dd if=/sdcard/wfixnv1.bin of=/dev/block/mmcblk0p5 ( enter )
5. Reboot Phone and DONE.

FOR FURTHER QUESTION, COMMENT BELOW

---